|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MP Jet Quality Metric Hardware, In Stock & Shipping!!!
|
|
|
|
|
|
|
|
|
|
Introducing First Ever, Elite Electronic Receiver Power & Ignition Kill Sliding Touch Switches with Incredible Low Standby Current (0.05mAh)!!! (Yup We Did It Again)!!!
The Elite Sliding Touch Switch is an electronic device that can be used to turn ON and OFF the electronics in your RC model. It can replace any electronic or mechanical switch. Features configurable touch sensitivity, last power-on status is stored in the internal memory, and very low standby current.
You do not need any additional tools to power up your model (such as a magnet in the case of a magnetic switch). The advantage of an electronic switch is that it offers a virtual unlimited ON/OFF cycle, unlike mechanically operated switches.
The faceplate contains an integrated LED to indicate the ON/OFF status of the switch. Should any of the devices become disconnected from the switch, the device will stay ON and switch will remember its last state.
|
|
|
|
|
|
|
|
|
|
18 Channel Jeti Central Box 310 & 320 Power/Signal Distribution Systems with Built In Voltage Regulator w/Tx Adjustable Output (5V-8.4V) and Integrated Telemetry Expander.
The Jeti Central Box 320 is fully programmable switchboard with two (2) independent, stabilized power inputs with single voltage regulator (20A Continues/80A Peak) designed for complete power and signal management of servos with great emphasis on safety. The Jeti Central Box 320 has a unique design that provides overload protection for up to 10 Standard (up to 415 oz/in, 30 kg/cm) and 8 Ultra Torque (up to 830 oz/in, 60 kg/cm) servos. The Jeti Central Box 320 features true Battery Redundancy, Ditex Servo Telemetry, Jeti EX Telemetry, and up to three (3) receiver inputs (2x 2.4GHz and 1x 900MHz) with serial (PPM, EX Bus) output for complete Power & RF Signal Redundancy. In addition the Jeti Central Box 320 has up to four (4) independent E1/E4 telemetry inputs. The onboard BEC allows the output voltage for the servo to be adjusted from 5V to 8.4V in 0.1V steps using Jeti Transmitter Device Explorer interface.
With Jeti Duplex 2.4GHz DC/DS transmitters, the full potential of the Central Box can be used, such as easy way to wirelessly configure the Servo Outputs, Ditex Servo & EX Telemetry, Fail-Safe Setting or Function Assignment.
|
|
|
|
|
|
|
|
|
|
Get Up to 22 Channels Using Jeti Central Box 210/220 & Central Box 100!!! (Sorry Spektrum/Futaba Cannot Do That)!!!
After receiving numerous questions regarding getting extra channels while using Jeti Central Box 210/220 we have come up with elegant configuration that uses power from CB210/220 servo port 9/10 for Central Box 100. This way you can have up to 20 high power servos connected to the system and still have full battery telemetry & redundancy.
If you connect Telemetry to the CB100 and use CB100 only for noncritical functions (Gyro, Lights, Airbrakes…) you can get away with a single power lead and go up to 22 servos.
|
|
|
|
|
|
|
|
|
|
Spring Cleaning: Store Display Plug & Play Opale Paramotor Power 2.7/3.67m Wing/Lucas Pilot/Mezon ESC/AXi Motor w/Optional Jeti Telemetry & Tons of Finished Details (One of a Kind)!!!
Designed with the easy handling that you have come to expect from an Opale single skin wing, the Power 2.7 is naturally gifted when it comes to dancing with the wind. During the first soaring flights, facing a 35km/h wind and lightly ballasted, we were very surprised by the high efficiency of this wing. The wing cuts lines through the wind like a sushi chef cutting a Maki roll with his knife. Under power, in combination with a Backpack L and a Lucas Pilot, the wing did not flinch and the handling was just as precise.
Recommended battery: 4000-5000mAh 6S
Condition of item: Store Demo, Test Flown, Like Brand NEW, Added Extra Features
|
|
|
|
|
|
|
|
|
|
Secraft Parts and Hardware is Rolling In, Web Pages Updated Daily!!!
|
|
|
|
|
|
|
|
|
|
|
|
|